List of IssuesDocument Types

Volume,Issue6,1999
Issue Cover
  • Fermentation Behavior ofCorn-Germ Dough

    Issue 6, (1999)
    Abstract:By the experiment of the fermented dough volumes with different contents of corn germ-residue. The effect on the gas-retaining and mature time were analyzed. The results showed that the effect of corn germ-residue on gluten structure and the change of carbon sources available for yeast directly affected the maximal volume and fermenting rate of fermented dough. As the quantity of corn germ-residue increased, the maximal volume decreased and the fermenting time was shortened. When addition amount of corn germ-residue was not more than 3%, the volume of fermented dough was near the same as that of flour special for bread; When addition amount of corn germ-residue reached 9%, the volume of fermented dough will be about 18% down.  
      
    1
    |
    7
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • The model of Post-dynamic Recrystallization of A508c1.3 Steel

    Issue 6, (1999)
    Abstract:The post dynamic recrystallization of A508c1. 3 steel is investigated by means of hot simulation and quantitative analysis of metallography. It was discovered that there is no distinct influence of percentage of dynamic recrystallization on meta-dynamic recrystallization. The model of post-dynamic recrystallization has been obtained by using multivariate nonlinear regression analysis.  
    Keywords:nuclear forging,A508c1. 3 steel,post-dynamic recrystallization,meta-dynamic recrystallization  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Application of Object-Oriented Technique to Graph Simulation of Mechanical System Motion

    Issue 6, (1999)
    Abstract:The method using Object-Oriented Programming Technique to build the geometric model of mechanlcal systems is introduced. There are two kinds of objects in the geometric model of a mechanical system: the graphs and the joints (that is, constraints). The basic graph class which has the common attributes of all graphs is constructed. Then, different graph classes, such as the box class, the cylinder class, the circle class, and so on, are derived from the baslc graph class. These classes inherit all the attributes belonging to the basic graph class. The joints are special graphs, so the basic joint class also can be derived from the basic graph class. All Joint classes inherit all the attributes of the basic graph class and the basic joint class. This method is hlghly efficient, and easy to realize and to expand.  
    Keywords:mechanical system,graph simulation,geometric model,object-oriented programmig technique  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Comparative AdvantageAnalysis of Agricultural Products

    Issue 6, (1999)
    Abstract:According to the theory of free trade and the Standard International Trade Classification(SITC), the comparative advantage of international trade of section and main agricultural product in China from 1987 to 1996 was evaluated, the comparative advantage of international trade of different agricultural products was determined, the time series property of change in China agricultural product's comparative advantage was analyzed, and the reasons of forming and changing of China agricultural product's comparative advantage from the viewpoint of factor endowment was discussed. Moreover, the econometric models have been developed.  
      
    1
    |
    8
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Medium for Fermentation ofPomace IntoFeeding Protein

    Issue 6, (1999)
    Abstract:On the basis of the stains combination acquired by screening experiment, the experiment of effect on the fermentation of pomace into feeding protein was carried out through among 4 inorganic nitrogen sounces and 12 byproducts or wastes from processing of agricultural products. The results showed that carbamide and ammonium sulfate were suitable to be used together as nitrogen source, the amount of carbamide and ammonium sulfate is 1.5% and 2% respectively. 12 kinds of byproducts or wastes from processing of agricultural products can all be used as a complement for pomace fermentation as the increasing rates of protein of their fermented products were all quite high. Among them, bean cake, rapeseed cake, cottonseed cake and spent brewer's grain were more suitable.  
      
    5
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Construction andApplication of Evaluation Index Systemof Agricultural Industrialization

    Issue 6, (1999)
    Abstract:Based on the understanding of agricultural industrialization management, and considering the source of basic information and its feasibility to quantification. A evaluation index system of agricultural industrialization was established, and put forward the relevant evaluation method. Taking the Baiyin city as an example of analysis, some primarily conclusions were obtained.  
      
    0
    |
    8
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study on Tensile Strengthof Fiber Soil StabilizationWith Portland Cement

    Issue 6, (1999)
    Abstract:The tensile strength and toughness of soil stabilization with portland cement mixed with fiber obtained is higher than those of the soil stabilization with portland cement. The regression on tensile strength with portland cement mixed with fiber was derived using orthogonal experiment. The tensile strength of fiber soil stabilization with portland cement was increased with dosage and length of fiber while the former was more effective than the latter.  
      
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • A Clustering Method for Ordering Samples and Its Utilization in Study of Farm Mechanization Level

    Issue 6, (1999)
    Abstract:A clustering method for the ordering samples is discussed based on the dynamic programming. It can be used to identify the breaking points and divide the sample into some sub-samples at where there are significant differences between the neighbor sub-samples, and obtain the optimum clustering results under a certain criterion. This method has been used in the evaluation of farm mechanization levels of different provinces in China. The results proved that this method is practical.  
    Keywords:ordering samples,clustering method,farm mechanization level  
    0
    |
    7
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study on TownEnvironmental Pollution and Countermeasure

    Issue 6, (1999)
      
    1
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study of Problems andCountermeasures of China''''s Regional Grain Balance

    Issue 6, (1999)
    Abstract:Based on studying supply-demand status, comparative advantage, regional distribution, yield fluctution and sustainable development, which are tightly correlative to regional grain balance problem, target pattern and concrete countermeasures are presented.  
      
    0
    |
    7
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Research and Design onCollector ofUsed Plastic Film on Farm Field

    Issue 6, (1999)
    Abstract:A plastic film collector was invented with analysis of motional tracks and experiments. The working principle and designing parameters of the collector were introduced. Experiments indicated that this machine has some advantages such as high working reliability, low energy consumption, and simple structure.  
      
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study of MovementParameters of SweepAuger of Counter-flow Drier

    Issue 6, (1999)
    Abstract:The performance of the counter-flow drier is effected seriously by the kinematic parameters of the sweep auger, especially the revolution speed. The kinematics and dynamics analyses of the auger were carried out, and the expression of the revolution speed of the auger was developed. Therefore, the rational values of the revolution speed can be obtained in the stage of drier design. The test results showed that the practical requirements can be met by the optimal parameters of the auger.  
      
    0
    |
    7
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study on Dynamic ProcessesSimulation of Hydraulic Equipment System of Pumped Storage Plant

    Issue 6, (1999)
    Abstract:On the basis of the operating characters of mixed-flow pump-turbine in pumped storage plant, the simulation model, which is of complicate hydraulic system's, of rejection transient when the unit was working as turbine, were founded through the internal analysis method and the elasticity was also considered. The simulation model of the rejection transient was developed through the method of process interaction. The corresponding simulation software was developed according to the operation situation of Shisanling pumped storage plant.  
      
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Coupling Effects of Waterand Fertilizer on CornYield With Drip Irrigation

    Issue 6, (1999)
    Abstract:Field experiments on the coupling effect of water and fertilizer on the intercrop of summer corn with drip irrigation have been conducted. The results showed that there are 4800m3 water per hectare of summer corn can be consumed, and applying N and P2O5 at rates of 175k.hm-2 and 145k.hm-2 respectively in entire corn season, yield of summer corn has reached more than 9450k.hm-2, and WUE(water use efficiency) over 1.9kg.m-3. The effective measures can results in obvious effects of water-saving and yield-raising.  
      
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Optimal Conditions of Bilevel Quadratic Multiobjective Programming

    Issue 6, (1999)
    Abstract:Bilevel programming models can be used efficiently to describe the hierarchy decision system. A class of bilevel quadratic multiobjective programming models is introduced. The definition of solution and the optimality conditions of the solution are given.  
    Keywords:bilevel quadratic multiobjective programming,Pareto efficient solution,optimality conditions  
    3
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Batch Arrival for Two-stage Tandem Queuing System With Finite Capcity

    Issue 6, (1999)
    Abstract:The two stage queue system between the two stage service with finite capcity was discussed. Customers arrival are bulk input with poisson process. There are n parallel independent servers with expontenial in first stage. The second stage service is single server with pH-distribution. The Stationary condition and stationary queue length distribution are given in terms of matrix iterative solution. Block probability and block time probability distribution are given.  
    Keywords:bulk input,pH-distribution,matrix-iterative solution,block time  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Characteristics of Acceleration of Instantaneous Velocity Center and Its Application

    Issue 6, (1999)
    Abstract:The characteristics of the acceleration of the instantaneous velocity center(IVC) were presented, and the trajectory equation for pure rolling of rigid body (PRORB) was developed. The conclusion is that the acceleration of IVC is orthogonal to velocity centrode.In the light of this, not only the geometric motion analysis method for PRORB can be included in normal analysls for rod-type system motion, but also its computational process can be simplified.  
    Keywords:motion analysis,instant center,acceleration geometric method,orbit  
    8
    |
    10
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study on PTO Driven Disc Cutter

    Issue 6, (1999)
    Abstract:The power driven disk as a residue cutting component was developed. The theoretical analysis, soil-bin test and field test showed that the PTO driven disk cutting parts have a lot of advantages in cutting the crop residue mulching layers.  
    Keywords:cutter,straw,driven disc,  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Development of Low Alloyed Sb-Cr As-Cast Ductile Iron

    Issue 6, (1999)
    Abstract:Based on the detailed investigation of the influence to microstructure and properties of ductile iron by Cr and Sb, it has been shown that neither Cr nor Sb promises a QT 600-3 property on module 37 mm castings expect Sb-Cr composite alloying. The analysis indicated that Cr and Sb are good couple in alloying. The as-cast QT 600-3 property can steadily reached by production testes.  
    Keywords:as-cast ductile iron,compostie alloying,Sb-Cr composite  
    1
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • A Simple Calculation Method of Nonfull Symmetry Four Outriggers Reaction for Construction Machinery

    Issue 6, (1999)
    Abstract:A simplified mathematical model for solving construction machinery outriggers reaction calculation problems is developed. Calculation on a simulatlon construction machinery are carried out using that model, the results of comparing experiments with calculation showed that the simplified mathematical model is correct and feasible. Based on the model, analyses of Four and three outriggers reaction during turning round of arm are put into practice.  
    Keywords:construction machinery,nonfull symmetry,outrigger reaction,calculation method,  
    1
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Adapt Design of MIS for Graduate Assignment in Dynamic Information Environment

    Issue 6, (1999)
    Abstract:The dynamic information environment of the MIS for graduate assignment and its influence to the life-span of management software have been developed. The problem adapt to dynamic environment in MIS developing was pointed out. Based on the design and practice, some key problems which have to be solved while designing management software adapt of dynamic information environment were expounded, the inter-relationship between software function design and the quality of its operators was expressed.  
    Keywords:MIS developing,information environment,dynamic adaptability  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • An Image Edge Detection Algorithm Based on Fractal Character

    Issue 6, (1999)
    Abstract:An image edge detection algorithm based on fractal character was developed. The method was rooted in the self-similarity of fractal image. The results of experiment showed that the proposed new algorithm for image edge detection was valid and effective.  
    Keywords:image processing,image edge detection,fractal,  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Efficiency Analysis of Building DEM

    Issue 6, (1999)
    Abstract:The general theory and method of building DEM and the factors influencing the efficiency of building DEM are presented and analyzed. The key of improving the efficiency of the building algorithm is to improve the storage structure of dispersed sampling data and the search algorithm.  
    Keywords:DEM,model,algorithm,efficiency analysis,  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Methods of Helicoid Modeling and Parametrization Design Using AutoCAD R14

    Issue 6, (1999)
    Abstract:The methods of the helicoid modeling were developed using the 3-D design function of the AutoCAD R14. The parametrization design of the helicoid has been realized by using the AutoLISP. The 3-D mould-making function, therefore, of AutoCAD has been extended. The helicoid model with different shapes of sections can be built by the methods presented in this paper.  
    Keywords:AutoCAD,helicoid,AutoLISP,  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Study on Product Information Modelling Technology of Rotation Parts Based on Feature

    Issue 6, (1999)
    Abstract:The integrating ways of CAD/CAPP and the relations between the way to describe prouct and to integrate their information were solved. It approached the exchange of product model data between CAD and CAPP by setting up a product data definition system which based on the feature. The model developed can be used for describing the information of the parts and setting up the technical rules intelligently.  
    Keywords:feature,product definition model,integration system  
    0
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Realization of An Application System for Multimedia Database

    Issue 6, (1999)
    Abstract:A database search system providing with multimedia function based on the application of Powerbuilder 6.5 and SYBASE SQL Anywhere database was developed and realized. That system, besides providing with all traditional database search functions, provides with database dynamic maintenance function and the support function for displaying multimedia information. In this system many advanced function of Powerbuilder 6. 5 were fully utilized, words, pictorial and video materials can be put together successfully, not only satisfied all needed functions of that system, but gives users aesthetic feelings.  
    Keywords:database,multimedia,search,Powerbuilder,SYBASE  
    9
    |
    6
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27
  • Effects of Soybean on Yield and Texture of Tofu

    Issue 6, (1999)
    Abstract:Effects of Soybean on the yield and texture of Tofu are reviewed. The variety of soybean plays an important role in the yield and texture of tofu. The coagulation of soy protein was in fluenced by the content of phytic acid in soybean. Not only the content of protein in soybean but also the constitute of soy protein has effect on the yield and texture of tofu. The relation between soybean and the yield and texture of tofu is relatively complex.  
    Keywords:soybean,tofu yield,tofu texture  
    9
    |
    12
    |
    0
    <HTML>
    <L-PDF> <Meta-XML>
    Updated:2024-02-27